Instructions for installing Nano panels directly on beautiful walls

Tips to help the project Construction of Nano panels Directly on the wall has durability / beauty that lasts with time in the article below!

B1 Prepare tools to construct Nano panels

Nano Panels constructed with the following tools:

• Stainless steel keel
• Stainless steel nails or screws
• Hammer or screwdriver
• Kosmos glue bottle
• Measuring tools: laser measuring device, ruler,…
• Cutting tools: Handheld cutter, cutter,…
• Marking tool: Pen or ink pad
• Panel accessories: moulding, molding

B2 Renovating wall surfaces with Nano panels

The wall of the house is very easy to degrade if there are no measures to prevent moisture. The condition of peeling, mold, cracks on the wall surface will adversely affect the life of the panel if we do not find a way to handle it before installation.

How to renovate a flat wall

If the wall surface is peeling, we need to remove all the rough crust on the wall surface by scraping. After that, we proceed to smooth the wall surface more flat. Finally, we paint a layer of primer (preferably waterproof paint) on the wall surface.

We can use plaster to improve the uneven condition of the wall. In case the wall surface is too rough, we should fill the foundation with cement mortar.

B3 Measure and cut Nano panels to the required size

We can easily cut Nano panels with a paper cutter. However, in locations that require meticulousness such as electrical outlets, we should use a handheld cutter to fine-tune.

B4 Apply glue to the back of the Nano panel

Construction of Nano panels It is required to use specialized glue (Kosmos Glue). We will apply it in a zigzag pattern so that the glue layer is evenly spread when pressed against the wall.

Note: The glue layer must be located a small distance from the edge to avoid the glue spilling on the surface.

B5 Fix the Nano panel directly to the wall via screws and stainless steel screws

To fix the Nano panel on the wall, we must use more Stainless steel keel. This is an accessory to be used by attaching wall paneling. With stainless steel screws, we will fix the keel and the panel on the wall. If you do not use stainless steel screws, you can still fix the keel by driving nails.

Note: 1 panel about 3m long needs to be used at least 7 chickens.

B6 Install the remaining Nano panel

Nano panels are assembled together with locks. When installing the positive seam into the negative seam of the panel, we will cover both the nails and screws, even the joints will not be clearly seen, ensuring the highest aesthetics for the project.

For areas where the wall is higher than the length of the panel, it is necessary to perform a panel connection.

• The trick for constructing Nano panels without revealing seams is to cut them straight or at an angle 30 degrees.
• The trick to installing Nano panels at a right angle is to cut the panel at an angle 45 degrees.

B7 Complete the Nano panel construction project with accessories

Decorative accessories for the construction of plastic wall panels

• Pointing the back of the wall: installed in the center of the wall.
• Skirting board: install the position adjacent to the floor.
• Bare neck: install ceiling position.
• Ending: edge cover mounting, mounting end position.
• End brace: similar to the end molding (designed according to each pattern).
• Negative angle brace: mounting in the inner corner or in the middle of the wall as a wall only.
• VU corner brace: outside corner mounting, 90 degree perpendicular position.

Note: You should choose accessories that match the same model or color to increase the aesthetics. PVC fittings are installed with special glue.

Install molding and splints at the edges of Nano panels.

Install skirting boards for Nano panels.

Construction of Nano panels directly on the wall requires us to invest a lot in the wall renovation process. Otherwise, you can install the panel on the skeleton. Any problems during construction can be solved via Hotline: (+84) 903 093 221. Kosmos Vietnam will answer all your questions as soon as possible!