Instructions for the correct construction of stone imitation plastic panels
The article will show you how construction of imitation stone plastic panels (stone-grained pvc) the right technique for beginners. Help readers can manually install this interior panel in the most aesthetic way.

Choosing the installation plan of imitation stone plastic panels
Before embarking on construction of imitation stone plastic panels, you must determine the most suitable installation plan. The plan depends on the work surface, specifically:

After determining the plan installation of imitation stone plastic panels, we will proceed to measure the project. Next is the design drawing. Finally, order the supplier with the appropriate number of panels according to the measurements.

Note: The use of a skeleton will create a void between the panel and the wall. This is not a product defect, so the warranty policy is not covered.
Prepare tools for construction of imitation stone plastic panels
Tool construction of imitation stone plastic panels not much, including:
- Stone grain PVC panels (Main material).
- Specialized glue: Stick the panel on the wall/frame.
- Double-sided tape: Fix the panel while waiting for the special glue to dry.
- Panel Accessories: Sigh only, aluminum strip for PVC stone-patterned panels,..
- Measuring Instruments: Tape measure, laser measurer, etc.
- Cutting tools: Knife, Cutter, ..
- Support tools: Racks, ladders,..

Carrying out the installation and construction of imitation stone plastic panels
The article will guide the steps to install pvc imitation stone panels according to each specific plan as follows:
B1 Surface treatment of imitation stone plastic panels
- Clean the surface of the work to ensure the adhesion of the panels.
- For cement walls, it is recommended to apply a layer of mastic (wall putty), to increase the adhesion of the panels.
- Because the panel is thin, the size of the frame is large should not be too thick.
- The distance between the skeletons is not more than 50cm.
- The position of the plate connection needs to be installed with a double skeleton system so that the joint is on the skeleton.
B2 Measure and cut the stone grain pvc sheet to the required size.
We trim and refine the panel with a cutting tool to match the design drawings.

B3 Use specialized glue & double-sided glue to the back of the sheet.
- Apply glue to the entire back of the panel.
- We stick the tape at the four corners and spread the glue points on the edges.
- Specialized glue is injected into the skeleton contact position.
- We put tape on the skeleton.


B4 Fix the faux stone plastic sheet onto the structure
- You apply pvc imitation stone to the flat wall.
- Nail in hard-to-see locations such as dark grain lines and high locations.
You apply the panel to the skeleton.


B5 Installation of accessories for stone grain pvc panels
Please inject glue into the gap where the accessory needs to be attached. After attaching the accessories, we will add paper tape on top to secure it.
- Accessories at the position of the eyelid: T brace, H brace.
- Accessories in the perpendicular position: V brace
- Accessories to create corner accents: Inner corner brace, outer corner brace.
- Accessories to create accents on the wall: Painting, molding belts, ceiling moldings,...


B6 Cleaning the surface of imitation pvc panels
At this time, we will perform the operation of removing the plastic sheet on pvc imitation stone and then wipe the surface of the work with a damp cloth to clean it.
Video of construction of pvc panels with stone pattern.
Note when constructing fake stone plastic panels
You should avoid exposing the panel to direct sunlight and absolutely do not install it outdoors.
Tape on the surface to secure the panel at the curved corner. This is only temporary and will be removed at a later time.
Need to fix the edge of the plate to avoid warping and warping when using
In case the glue spills on the panel.

Items of installation of imitation stone plastic panels

Summary, guide Construction of imitation stone (pvc stone grain) Correct technique has been fully conveyed in the article above. Hope you can apply it conveniently and quickly. For more specific advice on stone-grained PVC panels, you can leave a comment below or contact via Hotline: 0903.093.221