Instructions for installing 5-wave ASA plastic wall cladding.

Install the 5-wave ASA plastic wall cladding (code G-5S190X20) by securing the tongue and groove joints with stainless steel brackets and screws. The panels are connected to each other via tongue and groove joints on the panel edges.

ASA G-5S190X20 corrugated plastic slats weigh 3,45kg/slat, are lightweight, and can be directly installed on stable walls such as interior walls or walls with a flat surface (difference in height not exceeding 2mm/1m).

Exterior ceiling and wall cladding projects must be constructed on a frame that meets the following four conditions:

1. Durable material: Galvanized steel bars or stainless steel bars.
2. Sturdy dimensions: Bar thickness ≥1,2mm, side length ≥25mm.
3. Safe distance: Distance between bone bars ≤30cm.
4. Construction in the correct direction: The support beams must be installed perpendicular to the direction of the panel installation. Specifically, for vertical panel installation, install horizontal support beams; for horizontal panel installation, install vertical support beams.

Step 1: Prepare tools and materials for installing the ASA G-5S190X20 5-wave plastic louvers. wall

8 essential materials needed when installing ASA G-5S190X20 5-wave plastic louvers. wall the:

1. Reinforcing bar (material: stainless steel, galvanized steel; dimensions: side ≥25mm, thickness ≥1,2mm)
2. 5-wave ASA plastic lamella (G-5S190X20)
3. ASA plastic V-shaped trim (G-V45X45)
4. Iron anchor
5. Stainless steel flathead screws (using the flathead to securely fasten the screw to a rigid support beam)
6. Copper nail
7. Kosmos Exterior Glue
8. Stainless steel kettle

7 essential tools for installing ASA G-5S190X20 fluted panel cladding. wall These include: angle grinder, drill, welding machine, laser level, tape measure, protractor, and nail gun.

Step 2: Insert the metal anchors. wall, creating a connection between wall and the support frame for the fluted ASA plastic panel (G-5S190X20)

We need to create a connection between wall and the frame supporting the ASA plastic sheet is secured with metal anchors; the specific steps are as follows:

1. Drill holes in the wall using a drill.
2. Insert the metal anchor into the drilled hole.
3. Tighten the anchor bolts.

Metal anchor bolts are typically sized 6–12mm, and the drill bit should match the anchor bolt diameter.

The spacing between the anchors corresponds to the spacing of the reinforcing bars, for example:

How to install steel anchors into a wall when the support beam is horizontal.

How to install steel anchors into the wall when the support beam is vertical.

Tighten the anchor bolts if the support bar is horizontal.

Tighten the anchor bolts if the support rod is oriented vertically.

Step 3: Erect the frame when installing the 5-wave ASA plastic louvers. wall out side

To fix the skeletal frame in place wallWe weld the reinforcing bar to the steel anchors.

ASA plastic 5-wave louver frame for construction wall Outdoor applications need to meet the following 7 criteria:

1. Made of stainless steel or galvanized steel bars.
2. The dimensions of the bone strips are ≥25mm.
3. Bone thickness ≥1,2mm.
4. The spacing between the reinforcing bars should be ≤300mm (≤30cm).
5. The spacing between the double bone bars is 5mm.
6. The welded joints of the support beams need to be sanded smooth and coated with anti-rust paint.
7. The gap between the frame and the wall is 7-10mm for installing the ASA plastic V-shaped trim.
8. The ceiling frame has an outward slope of 2-3% (to prevent water accumulation).

Erect a horizontal frame when installing ASA plastic cladding panels vertically.

Erect a vertical frame when installing horizontal ASA plastic cladding panels.

Step 4: Install the 5-wave ASA plastic louvers (G-5S190X20) onto the upper frame. wall

Secure the 5-wave ASA plastic louvers (G-5S190X20) to the upper frame. wall Using Kosmos exterior adhesive, stainless steel brackets and screws, specifically:

1. Apply adhesive to the frame before installing the cladding panels.
2. Place the fluted ASA panel (G-5S190X20) in the position where adhesive has been applied to the frame.
3. Attach the brackets to the grooves of the fluted panel, and secure the panel to the frame by drilling screws into the holes in the brackets.
4. Install a male tongue and groove joint to conceal the female tongue and groove joint of the ASA plastic panel.

Perform the process of securing the female and male tongue-and-groove joints continuously until the entire wall surface is covered. A gap of 7-10mm should be left at the end point against the wall for installing the V-shaped trim.

Case 1: Installing 5-wave ASA plastic louver panels onto a horizontal (vertical) frame.

Here are 3 things to note when installing ASA G-5S190X20 5-wave plastic cladding panels onto a horizontal frame:

1. G-5S190X20 wall panel for vertical installation.
2. Install the wall panels flush against the wall, from left to right or right to left.
3. The male groove of the first panel faces the wall, and the female groove faces outwards.

Case 2: Installing 5-wave ASA plastic louver panels onto a vertical (horizontal) frame.

Here are 3 things to note when installing ASA G-5S190X20 5-wave plastic cladding panels onto a vertical frame:

1. G-5S190X20 horizontal panel.
2. Install the panels from bottom to top.
3. The male groove of the panel faces downwards, and the female groove faces upwards.

Step 5: Install the V-shaped edge trim. wall ASA G-5S190X20 fluted plastic panel cladding

There are two ways to secure the V-shaped trim to the ASA G-5S190X20 fluted plastic panel wall cladding:

1. Secure the trim with adhesive and stainless steel screws (flip-top/fish-tail type), with the screw holes spaced ≤300mm (≤30cm).
2. Secure the trim with adhesive and a nail gun, ensuring the nail holes are spaced ≤100mm (≤10cm) apart.

In addition to wall cladding, customers can also Ceiling cladding for balconies and patios using 5-wave ASA plastic slat panels G-5S190X20.

Proper installation of ASA 5-wave plastic wall cladding panels will result in a beautiful, durable finish and a lifespan of 5-10 years. If you require further assistance, please contact us. Consulting on construction methodsPlease contact us at this number. 0932.067.388 For the quickest and most accurate support.